how to clean mass air flow sensor chevy equinox

But if you clean your cars MAF sensor regularly you can avoid that 300 repair and keep your engine running at top efficiency. Pull out the air flow sensor and clean it properly If you need to replace it with a new one install the new sensor instead of the old MAF sensor Turn the engine on and leave it like that for 5-6 seconds Now turn it off and connect the MAF sensor with its harness Youll see DTC P0102 popping up on the dashboard.

7 Symptoms Of A Bad Mass Air Flow Sensor

Install the new MAF on your Chevrolet.

. Chevrolet Equinox MAF Sensor Cleaning Replacement Guide - 2018 To 2022 - Ecotec 15L Turbo I4 Engine - Picture Illustrated Automotive Maintenance DIY Instructions Chevrolet Equinox MAF Sensor Replacement Guide How to clean or change the mass air flow sensor in a 3rd generation 2018 to 2022 GM Chevy Equinox Ecotec 15L. Now well move on to the very delicate cleaning of the flow meter filaments. They are presented loosely in order from most to least likely.

Press the red clip slightly to unlock it. Remove the screws that hold the mass airflow sensor in place. You have to be very watchful in any other case your mass air flow sensor will be permanently damaged.

Unplug the part from the vehicles electrical system. Step 3 Clean the MAF Sensor To clean your MAF sensor simply take a solvent and spray it onto a paper towel. Push in on the tabs of the connector and unplug it from the MAF sensor.

Spray at least 10 spurts of MAF cleaner onto the sensor and then let it air dry for an hour or until completely dry. With the Chevy Equinox P0101 means the the Mass Air Flow MAF sensor has a RangePerformance problem. Look for the little black box attached to the air intake hose.

Here I demonstrate how I cleaned my manifold absolute pressure MAP sensor and mass air flow MAF sensor in 2012 Equinox with 24L ecotec engine. If you like you can also spray down the sensor with some WD-40. Let soak the lower part of your mass air flow sensor not the plug part in acetone or another solvent for a few minutes which will take out most of the grime.

The Intake Air Temperature IAT sensor is also built into. Itll have a large electrical connector plugged into it. Locate the mass airflow sensor near the engine air filter housing.

2 Remove the Sensor. Simple hand tools will be all that you need to complete the job. Put everything back together and start the engine.

Unplug the electrical connector from the mass airflow sensor. You have to be very cautious otherwise your mass air flow sensor will be permanently damaged. Locate the mass air flow sensor by consulting your owners manual.

Mass air flow MAF sensors measure the amount of air entering the engine. Step 1 Remove the MAF sensor. MAF Sensor Dirty Over the course of its life the MAF sensor will often get so covered in grime that itll no longer get an accurate reading.

Reliable and quiet your Chevrolet Equinox small crossover SUV is perfect for highway driving and it gets respectable gas mileage as well. Tighten the screws so that they are snug. Locate the MAF Sensor Itll be in between the air filter and the throttle body.

Mass Airflow Sensor MAF. Carmakers like Ford and Chevrolet recommend that you replace the MAF sensor 300 at that point. Get even more out of it with a new mass air flow sensor for Chevrolet Tahoe from AutoZone.

Today I show you where your Mass Air Flow MAF Sensor is located and how to remove and clean it. The mass air flow cleaner only costs about 7. Also do not use anything other than the MAF cleaner to clean the sensor otherwise the sensor may get damaged.

Do not use a cloth or cotton swabs to clean the sensor. Spacious and tough your Chevy Tahoe is everything you need for a great weekend away. We recommend that you clean the MAF sensor every time you change your.

You have to be very careful otherwise your mass air flow sensor will be permanently broken. Now well proceed to the very delicate cleaning of the flow meter filaments. With the help of a fine brush and solvent gently clean the two filaments of your mass air flow sensor.

Start by opening the hood. Let soak the lower part of your mass air flow sensor not the plug part in acetone or another solvent for a few minutes which will remove most of the grime. In case this isnt the MAF sensor article youre needing there are several more Ive written and you can find some of them here.

How To Test The GM mass air flow sensor Early Type. One way to protect that fuel economy is with a new mass air flow sensor for Chevrolet Equinox from AutoZone. Youll see it just down from the large air intake box on the far left.

If you are too afraid of harming it you can also clean them with a brake fluid in the form of an aerosol by spraying the jet on these filaments. This component allows more accurate readings of the air flow. Unplug the electrical connector.

How to Clean a Mass Air Flow Sensor 1 Unplug the Sensor Turn the engine off remove the keys from the ignition and let the engine cool. They can be cleaned but its easy to mess one up and you dont want to use a. Remove the Sensor- Take care not to damage the wiring harness or the connector pins that receive the harness in the MAF.

Then apply the solvent to the wire mesh on the front of the sensor and scrub in a circular motion with an emphasis on any oil residue that may be present.

2018 2022 Chevrolet Equinox Maf Sensor Replacement Guide 021